Download e-book for iPad: A Lesson Plan for Woodturning: Step-by-Step Instructions for by James Rodgers

By James Rodgers

ISBN-10: 1610351819

ISBN-13: 9781610351812

Writer James Rodgers has been instructing woodturning for over a decade. He took that have and wrote the e-book A Lesson Plan for wooden Turning to supply step by step guideline for starting turners. The ebook is designed as a self-directed direction in woodturning security, instruments and methods and builds upon itself with each one ability and venture. The initiatives concentrate on ability improvement and are documented with over 2 hundred colour images so the coed will see right slicing motions and positions. This booklet could additionally make a superb consultant for academics.

Show description

Read or Download A Lesson Plan for Woodturning: Step-by-Step Instructions for Mastering Woodturning Fundamentals PDF

Similar woodworking books

Good Woodworking (October 2015) by PDF

Sturdy Woodworking journal is the best journal for willing woodworking hobbyists alike. every month it bargains recommendation and information on quite a lot of woodworking subject matters, through stage-by-stage undertaking articles, in-depth technical positive factors, workshop advice and product exams. A devoted turning part caters for this crucial staff of woodworkers, whereas readers can use the unfastened Q&A provider to have their questions spoke back via specialists.

New PDF release: The construction of period country furniture

В книге interval furnishings info множество отличных чертежей и пояснений для изготовления мебели и других изделий из дерева

Read e-book online Wooden Clocks : 31 Favorite Projects & Patterns PDF

The main cherished clock initiatives from the pages of Scroll observed Woodworking and Crafts. contains grandfather clocks, pendulum clocks, table clocks, and extra.

Easy-to-Make Arts and Crafts Lamps and Shades by John D. Adams PDF

Trendy within the early twentieth century, Arts and Crafts-style lamps are well known back within the twenty-first century. The dependent simplicity of those necessary furniture will motivate craftworkers to attempt their hand on the good-looking tasks defined during this instructive handbook. First released approximately a century in the past, this step by step guide--with measurements for 16 projects--shows the best way to flip uncomplicated, reasonably cheap fabrics right into a wide selection of gorgeous and sensible Arts and Crafts tasks, between them transportable desk lamps, studying and piano lamps, a eating room dome, a lantern, a colour for a droplight, and wall-hanging lamps, in addition to a newel publish lamp, and an electrical candle sconce.

Additional resources for A Lesson Plan for Woodturning: Step-by-Step Instructions for Mastering Woodturning Fundamentals

Sample text

To determine w h et h er a fini sh w as easy or diffi cu lt to sand, [ sande d all three coats NE W WAT ER-BA SED FI NI SHES 27 with varying gr its of fresh paper. Thankfully, all of th e finishes I tested fell in th e easy to modera te range. In fact, several of the finishes were as easy or easier to sand th an lacq uer and she llac. For a high - gloss, rubb ed- ou t finish, I found that using 1,OOO- gr it and 1,200- grit we t abrasive paper (available at auto- bo dy su pply shops) pr ior to rubbing o ut w ith pumice and rotte nstone gave m e th e best results.

This was my first experi­ guns met all regulatory ence with HVLP spray requirements, but they equipment. were tremendous air hogs. Consuming air at HVLP technology may have remained that a rate of20 cu. ft. per simple had it not been minute (cfin) or for the South Coast Air higher, just one Quality Management spray gun District (SCAQMD) in Los Angeles. For required a lO-hp compressor. Large shops decades, high-pressure, compressor-driven spray equipment was the only game on the block. The equipment is extremely versatile, could accommodate conversion guns, but small, custom shops did not have the air power to run them.

W hen air is co mpr essed, water vapor in th e air conde nses to a liqui d . If not removed , the water that passes through the spray gun wi ll cause all kinds of finishin g problem s. The separato r also removes residual o il that's used for lubrica tion of the compressor. Internal mix or external mix H ighpressure spray guns are available in two type s: int ernal and ex ternal mix (see the photo an d drawings on p. The mix de signation is based on where the airstream is introdu ced into th e flu id stream .

Download PDF sample

A Lesson Plan for Woodturning: Step-by-Step Instructions for Mastering Woodturning Fundamentals by James Rodgers


by George
4.5

Rated 4.35 of 5 – based on 33 votes